Multiuse Configuration of BSNL Teracom Type 2 Modem (with 4 lan ports)

Discussion in 'BSNL broadband' started by jack_jonson2000, May 3, 2010.

  1. jack_jonson2000

    jack_jonson2000 New Member

    I have taken recently BSNL connection have been give TERACOM Tyep2( T-2B-Gawv1.4U10Y-BI) with 4 lan Ports . But they have done configuration for only one port because i was not able to connect internet on more than one PC . When two lan ports are connected to different Pc or even i am not able to connect 1 PC & 1 Laptop (wireless) so its now even configured for one LAN & one WLAN .
    I tried hard but was not able to configure the setting in modem settings at 192.168.1.1
    Please if anyone knows the setting let me know the same ....thanx in advance
  2. meetdilip

    meetdilip The Wizard

  3. jack_jonson2000

    jack_jonson2000 New Member

    Non of it seems to be working for me .... i have gone through the complete article in that link also downloaded the zip for settings but the interface(modem interface) shown there is altogether different from mine & has lots of changes in options so i m not able to do the configuration .... PLz help
  4. essbebe

    essbebe LEARNER

    TERACOM Tyep2( T-2B-Gawv1.4U10Y-BI)
    Assuming you know how to change settings, go to LAn page and enable DHCP and give a range.
    ( if somewhere you find UpNP box enable it also
    (optional)
    Reboot wait for 2 minutes.

    2.
    Now in each computer/ desktop/laptop
    Start Network Properties
    network Settings page
    Highlight TCP/IP
    properties
    Select Obtain Ip address automatically
    SAVE APPLY.

    If still problem
    Copy/paste ( without edit )
    start run type cmd ok
    typeipconfig /all

    I have most screen shots for this router and appears same siemens C2110
    menu pages ( less wifi )
    More...>>> on <<<<== Feedback!
  5. jack_jonson2000

    jack_jonson2000 New Member

    Still not working

    I have configured DHCP server for the range of 192.168.1.2 to 192.168.1.40
    and my computers have ip in same range ...then also i m able to connect a single PC at a time to internet. both the PC are LAN connected to Router i have also tried to ping the router from both PC's its working fine no data loss.

    Then to i m able to connect to net single PC at a time..have attached to some screen shots to get idea of modem interface...

    Attached Files:

  6. Indranil

    Indranil Member

    Your problem solution is very simple

    Use PPPOE on your modem instead of Bridge mode. Setup your Router in PPPOE mode and use user ID and password in there. In PPPOE mode you dont need to log in from your Computer Desktop. After that you can browse more then one computer.
  7. jack_jonson2000

    jack_jonson2000 New Member

    Thanx Indranil ... it worked ..thanx again
  8. Indranil

    Indranil Member

    You are Welcome :)
  9. meetdilip

    meetdilip The Wizard

    Ok........................
  10. Happydhillon786

    Happydhillon786 New Member

    TERACOM Tyep2( T-2B-Gawv1.4U10Y-BI)

    I have a BSNL Broadband Teracom wifi modem...!
    when i'm use to connect a Internet with a modem, it is give an error..
    please give me modem setting...
    and when i am try install its disk, its also give a error in middle..
    plz help give me full modem wifi configurations......:confused:
  11. essbebe

    essbebe LEARNER

    Last edited: Jun 8, 2010
  12. paritoshpanigrahi

    paritoshpanigrahi New Member

    How to access webpages from outside

    Hi all,
    I want to access my wabpages from outside internet. For that i have installed web server sw.
    But while accessing it showing me the router configuration page. I have dynamic ip. My router is bsnl type II modem(T2-B-Gawv1.4U10Y-BI.I tried to foreward the port but not successful. Can anybody tell me the detail procedure to overcome the problem. And another problem is that previously while i was typing 192.168.1.1 the router page was opening. But now it is not opening.
    Last edited: Jul 19, 2010
  13. essbebe

    essbebe LEARNER

  14. paritoshpanigrahi

    paritoshpanigrahi New Member

    I have already installed DynDSN sw for mapping ip address. While i m typing my ip or website name it showing me the router page. I have tried with c2112
    modem. it was successful. but now i have teracom wifi router. So please tell me how to forewaed port sothat i can access my webpages.
  15. essbebe

    essbebe LEARNER

    Post ipconfig /all.
    Copy/Paste data here.
    the Ip allotted say 192.168.1.X is to be entered in port triggering .
    Give your server address to check access.
  16. jatininfo

    jatininfo Guest

    use this to configure BSNL Tera com modem
  17. sachin1

    sachin1 New Member

    connection of two comp using lan on a single modem

    how can we do pppoe settings
  18. meetdilip

    meetdilip The Wizard

  19. essbebe

    essbebe LEARNER

    (A)
    There is still confusion about PPPoE settings.
    for some it means Using a "Dialer"in system and entering UserID/PW
    ( "Selected "Bridged" mode in wan page of any modem )
    (B)
    Always on PPPoA/PPPoE or PPPoE mode
    ( if " bridged" is unselcted and above PPPoE box is checked,
    you get another page to ENTER/STORE your USERID/PW
    You get connected to Internet automatically.

    Most screen shots show the second type.
    Select which one you need.
    Still need select from signature links below. "TERACOM" both modes available.
  20. sachin1

    sachin1 New Member

    thanks now i can do that thanks again

Share This Page